S-02 · GLASS · OS2 / OM3 / OM4
FIBER
OPTIC
INSTALLATION.
Single-mode and multi-mode fiber installed and certified for backbones, building-to-building runs, and data-center cross-connects. Fusion spliced, Tier 1 & Tier 2 tested, and terminated at rack-mount enclosures with full trace documentation.
01SPEC
- FIBER TYPES
- OS2 · OM3 · OM4 · OM5
- CONSTRUCTION
- Loose-tube · Tight-buffer · Armored
- CONNECTORS
- LC · SC · ST · MTP/MPO
- TERMINATION
- Fusion splice · Field-polish
- TESTING
- OLTS (Tier 1) · OTDR (Tier 2)
- SPEEDS
- 1G · 10G · 40G · 100G+
- ENVIRONMENTS
- Plenum · Riser · OSP · Direct-burial
- ENCLOSURES
- Corning · Panduit · Leviton
02WHAT WE INSTALL
01
Backbone & riser fiber
Vertical riser and horizontal backbone fiber between MDF and IDFs, sized for current and future speeds. Loss budget calculated during design so 40G/100G upgrades don't require repulling.
02
Building-to-building outside plant
Direct-burial, innerduct, aerial, and armored OSP runs between campus buildings. We coordinate trenching, install handhole vaults, and enter buildings with proper firestop and grounding.
03
Data-center cross-connects
MTP/MPO-based structured cabling with LC breakouts at each cabinet. Cassettes and trunk cables sized to spine-and-leaf topologies so switch upgrades don't touch the plant.
04
Fusion splicing & OTDR certification
On-site fusion splicing with heat-shrink protection in rack-mount enclosures. Bidirectional OTDR traces and OLTS insertion loss reports delivered per strand.
03TYPICAL PROJECTS
- Multi-building campus backbone
- Warehouse trunk between office and dock IDF
- Data-center MTP structured cabling
- Bandwidth upgrade from CAT to fiber uplinks
- Fiber to the WAP (FTTA) programs
- Outside-plant runs between buildings on one parcel
04FAQ
- Q-01
- OS2 single-mode is the right choice for backbone runs over ~300 meters, campus/building-to-building, and any path where 40G/100G upgrades are anticipated. OM4 multi-mode is common for short data-center and MDF-to-IDF links under 400 meters at 10G or 150 meters at 40G. We size the plant during design so future upgrades don't require re-pulling fiber.
- Q-02
- Yes. All splices are performed with a fusion splicer on-site, protected with heat-shrink sleeves, and terminated in a rack-mount fiber enclosure with proper strain relief. Splice loss is verified with OTDR bidirectionally.
- Q-03
- We deliver Tier 1 (OLTS insertion loss) and Tier 2 (OTDR trace) test results for every strand. Reports include loss budget vs measured loss, event-by-event OTDR traces, and connector-end-face inspection photos where required.
- Q-04
- Yes. We handle direct-burial, innerduct, aerial-lash, and armored outside-plant runs, including trenching coordination, handhole vaults, and building entry with proper firestopping. All OSP terminates in an indoor patch panel with a grounded splice tray.
- Q-05
- Yes. We terminate LC, SC, ST, and MTP/MPO connectors and can convert between them with cassettes. For 40G/100G spine-to-leaf we typically install MTP-based structured cabling with breakouts at each cabinet.
Should I use single-mode (OS2) or multi-mode (OM3/OM4) fiber?
Do you do fusion splicing on-site?
How is the fiber plant tested and certified?
Can you install outside-plant fiber between buildings?
Do you provide fiber connectors like LC, SC, MTP/MPO?
05RELATED SERVICES
QUOTE TURNAROUND · < 24H
Start a project with our crew.